Model: Decoding ballast technical parameters required Ballast appearance：35W/55WNew super slim digital canbus ballast Advantage:1: digital circuit design, than the average simulation and more stable, and the overall structure and the scheme which is the same as famous brand Hylux,2 decoding ability, 99% car canbus problem can be settled.3 new design high-grade shell.4 Lowest price. 一、Range The technical parameters required for the production of the Division I CAN-BUS 35W the HID ballast。二、Packaging and appearance requirementsSmooth surface of the product there is no obvious stains, scratches, no cracks, damage, deformation and other defects; connector should contact a reliable, no loose。三、Product Technical ParametersRated working voltagetest voltageInstantly enter the cold start currentRated input powerOperating voltage12V12V3.6±0.1A（12V）42±2W（12V）9±0.5V～16±0.5VRated output voltageExperimental output voltageRated output current13.5V output powerWork efficiencyOperating TemperatureAC 85VAC 80V - 92V0.4±0.1A（12V）35±1W≥80%-40℃～+85℃Ballast start interferenceBallast stable interferenceWhen the start of the ballast work to stabilize the current changesStart the instantaneous peak current ≤50mV≤20mV≤0.1A/Second≤28A 4、Project detectionSerial numberTest itemsTest methodsCriteria1Room temperature startEnter the room temperature DC 9V ± 0.5V DC 12V ± 0.5V DC 16V ± 0.5V three working voltageProducts can start properly lit, the lamp is off, flicker2Short-circuit protectionOutput short circuit for 5 secondsUpon removal of short re-supply, product normally start, no flicker3Open-circuit protectionOutput open circuit for 5 secondsOpen to eliminate the re-supply, non-extinguished lamp flicker4Reverse polarity protectionInput reverse for 5 secondsProtection current to 0 amps, reverse the elimination of re-supply, non-extinguished lamp flicker5Undervoltage protection9V ± 0.5V normal lighting 6Overvoltage protectionRated voltage to power lights. Slowly increased the voltage to the lamp goes off, the voltage value before the record light goes out; voltage decreased slowly to the lamp lit, the voltage value before the record light litThe input voltage is higher than 17 ± 1V lights off, lower than 16.5 ± 0.5V lights7High, low temperature and pressure to startTo +85 ° C, and -40 ° C ambient temperature for 2 hours, type 9V ± 0.5V operating voltage of 12V ± 0.5V, 16V ± 0.5V three kinds of startBallast after the normal start of the three voltage product tube without off, flicker8Cryogenic storageLow temperature of -40 ° C, chilled 2 hoursBulb at -40 ℃ in normal lighting9Hot workHigh temperature 85 ° C under normal work, keep 2 hoursProduct light bulb is working properly10High temperatureSwitching cyclesHigh temperature of 85 ℃, each lighting 24 minutes later, off 10 seconds, cycle 10 cycleAfter the test, the bulbs can not be damaged11DurabilityTestRoom temperature, continuous aging operating 36h, the occurrence of negative phenomena. (Where the quick flash of the frequency of 3 times / sec 18h, a total of more than 5 million times, no lights flash off phenomenon)After the test, the bulbs can not be damaged12High voltage outputMAX.23KV五，Market comparison： 一，This section electronic rectifier, in-house design trip computer monitoring line can be installed directly in the trip computer (with a computer scan) models, the need for external decoders and dummy load, fault lights or interference does not appear after installationand other phenomena, such as the Tiguan SAGITAR, MAGOTAN, JEEP Wrangler JEEP Compass, BMW 3 Series, 5 Series, Audi, IX35, Sonata, etc. can be easily installed, saving time, beautiful.Second, other electronic rectifier, no internal design of the full trip computer monitoring line, but the installation of a power supply box, generally a lot of cars are not normal use, such as JEEP Wrangler JEEP Compass, BMW 3 Series, 5 the Department. www.liwin-china.com