madworm/USB_inspection-light
LAYOUT FILES: USB powered inspection light for tight places.
Developer Profile
madworm
Discovered public repositories for madworm in the GitHub catalog.
madworm/Youyue-858D-plus-MCU-adapter
LAYOUT FILES: ATmega168/328 adapter board for the Youyue 858D+.
madworm/Youyue-858D-plus
CODE: Custom firmware for Youyue 858D+ (ATmega168/328P)
madworm/Coat-Button
LAYOUT FILES: Sewable blinky button for coats.
madworm/KiCad-Stuff
Various things to make working with KiCad easier. Most likely Linux centric.
madworm/AVR-ISP_pogo-plug_1.27mm
LAYOUT FILES: AVR-ISP adapter: 6pin (2.54mm) --> 6pin pogo-pins (1.27mm).
madworm/LED-strip_PWM
LAYOUT FILES: Tiny LED-strip PWM controller in 2 variants.
madworm/ledcandle
Flickering LED Candle Firmware
madworm/Pentax-S5z-LED-ring
LAYOUT FILES: LED ring for my old Pentax S5z digital camera.
madworm/KiCad-Logos
Logos and other potentially useful graphical elements for KiCad
madworm/Serial-Knob
LAYOUT FILES: Rotary encoder + microcontroller. Sends commands via serial.
madworm/MBI5030_starter-board
LAYOUT FILES: Simple breadboard starter board for the MBI5030. Includes 16 SMD LEDs for instant light.
madworm/MBI5030_demo
CODE: Arduino-ized code to talk to and configure the Macroblock MBI5030 PWM LED driver.
madworm/LED_port-status
LAYOUT FILES: Easily display the status of GPIO lines when using a breadboard.
madworm/LED-strip_PWM_IR
LAYOUT FILES: Small high-current PWM controller with IR receiver (ATtiny85 based).
madworm/LED-Square_PT4115
LAYOUT FILES: 50x50mm LED-Square with PT4115 LED driver.
madworm/SOT89-5_DIP
LAYOUT FILES: SOT89-5 to DIP adapter - e.g. for PT4115 LED driver.
madworm/SOP24_300_1.00_breakout
LAYOUT FILES: Simple breakout board for SOP24-300-1.00 chips (like MBI5030)
madworm/SOT23_DIP
LAYOUT FILES: SOT23-(3,5,6) to DIP-6 adapter
madworm/CapSense
LAYOUT FILES: Capacitive sensing experiments.
madworm/YauDL
LAYOUT FILES: (Y)et (a)nother (u)seless (D)ummy (L)oad
madworm/oshw-logo
The logo for open source hardware
madworm/avrispmkII_LUFA
CODE: LUFA / avrispmkII modification for easy linux/windows usage.
madworm/DSO_teaser
CODE + a little bit of hardware to test DSOs.
madworm/IR_raw_receiver
LAYOUT FILES: 38kHz IR receiver using ATtiny85 + TSOP38238
madworm/IR_remote
CODE: Arduino code for (xx8 chips). Receive raw IR signals with a demodulating IR sensor using a pin-change interrupt.
madworm/V3_x_boards_test
CODE: 8x8 RGB LED Matrix controller board V3: Test code. Arduino code. Designed for 168/328 chips. May need modifications for others.
madworm/rgb_led_toy_test
CODE: led ring board: This is what you want! Arduino code. Designed for 168/328 chips. May need modifications for others.
madworm/ATtiny_projects
CODE: various things for ATtiny micro-controllers.
madworm/MBI5168_DIP_breakout
LAYOUT FILES: Simple breakout board for the MBI5168 constant current LED driver. KICAD and Gerber files.
madworm/MBI5168_SMD_breakout
LAYOUT FILES: Simple breakout board for the MBI5168 constant current LED driver. KICAD and Gerber files.
madworm/Openbench_logic_sniffer_pull-U_D_wing
LAYOUT FILES: Adds convenient pull-up/down resistor selection (10k) for the Openbench logic sniffer plus selectable pull-up voltage (5.0, 3.3, 2.5, ...) for each bank. KICAD and Gerber files.
madworm/Kitchen_Lights
LAYOUT FILES: ATtiny24 (pre v1.10) / ATtiny2313 + MBI5168 controlled lamp with 32x superflux-class LEDs. Under heavy development --> unsafe to use!
madworm/Arduino---Code--Blocks
CODE: Compling the 'core.a' file for your architecture + compiling 'normal' code. This assumes you have a working avr-gcc, avr-libc and the avr-binutils installed! This is intended to run on linux.
madworm/8x8_RGB_LED_Matrix_Controller
LAYOUT FILES: 8x8-RGB-LED-Matrix controller using 4x 74HC595 shift registers. CPU: ATmega168/328. Arduino 'compatible'. Runs with code from 'V3_x_boards_test' repo. KICAD and Gerber files.
madworm/show_anim_video
CODE: 8x8 RGB LED Matrix controller board. Show animation(s) stored in FLASH/PROGMEM or sent from a computer. Arduino code. Intended for 168/328 chips. May need modifications for others.
madworm/RGB_LED_TOY
LAYOUT FILES: Led ring board with 8 RGB LEDs driven by an ATmega168-20AU TQFP-32 7x7 micro controller. KICAD and Gerber files.
madworm/MSOP10_DIP
LAYOUT FILES: MSOP10 / TSSOP8 to DIP adapter. Essential for breadboard prototyping. KICAD and Gerber files.